CETW Nov 6th - 7th

We are pleased to announce that Mesa Mundi Inc. is exhibiting at Customer Engagement Technology World (CETW), November 6-7 at the Javits in New York City and would like to invite you to visit us in Booth 434!

We'll have special guests from 4Productions and Touchtech AB at our booth throughout the show.  Additionally, we will be featuring a new automatic lift rolling cart stand for multitouch displays with a staggered manual tilt head.  The stand supports up to 55" screens or 120 lbs.  It uses a single post design with a housing on the back of the stand that adds a significant amount of rigidity to the system when in table orientation and hides the gas springs used to ensure you do not have a large display moving out of control.

For this weekends event prep, I wheeled the stand home and mounted a 40" Monolith, pictured below:

      

Look for the product listing in the days leading up to CETW!

Continue Reading

Coffee Table and Magnetic Marker Experiment

Finally! A coffee table build using a 40” Monolith in an all maple wooden enclosure.  This one lives in my house.  I find it funny how often I've built systems, built prototypes, and rarely have a fully assembled unit at my disposal for experimentation.  

A friend of ours fabricated the adaptive top portion onto our old Geek Chic prototype table build from the Locus days. The construction is all maple -- Geek Chic scrap and prototyping is still better than most purpose built tables. The Monolith sits fairly flush to the surface wood. It protrudes just enough to keep a smooth edge to edge transition from wood to metal.

The total build cost for this unit as a one-off custom build would be roughly 4600.00 USD -- not bad really, but still pretty high.

I'm currently using it to experiment with various non-direct touch systems such as cover glass with moveable, magnetic pieces. So far this has been a great build. The hardware is as follows:

  • 40” Monolith
  • 40” IR Touch Frame—This build is using a 4-point touch frame (can easily swap out the screen for another with more or less touch points—2, 4, 6, 10, 20, or more...)
  • 1/8” Tempered glass surface
  • Samsung ME40B Commercial display
  • Powder coated steel enclosure to hold the kit together
  • Zotac ID70
  • i3 2nd Gen Proc
  • 4 GB Ram
  • NVidia Discreet graphics adapter
  • Small, easily hidden package.
  • Surge rated power strip to enable single cable out from the table
    • Right now the PC and cables are just tucked underneath on the lower shelf. This will all be attached to a mounting system I’m hanging on the right hand inside wall. Easy to access but out of the way and visually clean.

 

The result is a quick and dirty interactive coffee table. The table design is such that the LCD hangs from the metal enclosure which clamps the touch and surface glass components together. The Monolith itself is held up on a small lip that exposes all of the inputs and output as well as the vents for the LCD—this allows for adequate ventilation and support for the metal enclosure which in turn carries the weight of the LCD and glass.

The short sides of the table are closed to allow for space to build our PC box and manage cables into a single exit point. The PC box will be movable from the right end to the left end in the event that I want to alter where the power cord exits the system without having to flip the LCD screen.

Current configurations are as follows:

  • Straight direct touch with no cover glass over entire unit. The Monolith surface glass is still present so touch actions are not occurring directly on the LCD.
  • Recessed screen and edging which allows for a top to be added to the unit which hides the touch screen until it is needed, desired. This build results in a slight drop after about an inch from the edge when the touch screen is exposed.
  • 1/4 inch tempered glass topper. This top allows the screen to be seen and used via keyboard/mouse or through the use of magnetic markers which are placed under the glass and then moved with a second set of markers from above.
I’m working on a small collection of markers with different properties, right now I have some thick ones and some thin ones. The thin ones should allow for button like actions as they can be lifted out of the range of the touch and then “dropped” to create touch actions—however, right now, these thin ones will stack if they are brought over each other—work in progress.

 

 

 

 

 

Below is a video showing basic interactions with my first pass test of thru-glass magnetic objects, Alea Magnetic Markers and Refrigerator Magnets!

 

 

The idea is inspired by the magnetic box toys you see at various science and childrens museums. The external markers can be any object with a nice strong magnet in it, such as a toy truck. The internal markers can be smaller cylinders or less obtrusive objects. The basic idea would be an interactive software that the physical, external objects interact with by manipulating the various "tool-tips" active in the application. The application featured is the Windows 7 Touch-Pack Lagoon screensaver -- still a favorite on my older test systems.

A final build would use glass that runs edge to edge or acrylic that hooked around the long edges. Additionally, I’d use clear stand offs rather than the black PC feet which I seem to have an endless supply of..

The key observation from this weekend experiment is that my kids love it! They have been having a great time moving the pieces around and seeing the interaction with the water and the fish. They're not new to the screensaver, but the physical objects certainly renewed their interest. 


The Lagoon screensaver has a neat feature where a touch event left in place causes the fish to gather and "nibble" at the touch point. In a traditional installation, a user has to hold still and let the fish come up to them. I've shown Lagoon multiple times at conventions and shows over the years and usually have to demonstrate this element. With the static markers, the fish always come out to play when the screen is idle -- a very interesting change in behavior and thus, expectation. My kids are fairly young, they have a hard time holding still long enough for the reward of a finger surrounded by fish. Using these objects, they simply had to -not- touch anything for a few moments to enjoy the arrival of our skittish friends.

As time permits, I will continue to experiment with this table configuration and post my observations.

 

 

 

 

 

Continue Reading

PAX East here we come!

This year's PAX East should be very interesting.  We have some new products to show as well as new software.  We will have some special guests at our booth; the d20Pro lead developer and two of the brains behind Machine Code Games.

Pick up your swords and spears, we have d20Pro demoing with a playable, mini arena scenario.  This is a quick intro to d20Pro setup which will be played directly from the booth, so stop on by!

Machine Code Games is getting their casual gaming on with a collection of games available for play on many of our touch screens.  There will be space for sit-down, casual board gaming with these talented developers.  

Last but not least, we will be debuting our newest edition to our multitouch touch screen line up.  We will have two of our new and improved touch screen systems on hand.  Help us name our new product line by submitting your ideas into the proverbial hat!  

We will be offering various show specials and events throughout the show.  Stop by often or follow us on twitter .

Stop by Booth 380 at PAX East for engaging multitouch gaming experience as well as our show discount.


Continue Reading

ZinFrameServer v5.5.x and X Slim Series Frames

Two big updates from the ZaagTech world.  The first is the X Slim Series frame.  This 19 mm wide IR Multitouch Overlay has a very "slim" bezel width.  The height from the touch surface measures in at 10.8 mm.  Keep in mind that with all of these overlays, whether their from Baanto, PQLabs or ZaagTech, you always need to add in the thickness of your adhesive and/or touch surface/acrylic.  

As a means to minimize added height ZaagTech includes a new selection of 3M double sided industrial tape.  This new material is grey and squishes down quite thin, adding no more than .25 mm - .5 mm.  I've had a lot of success with the material on attaching to both plastic and metal.

The performance on the X Slim frames are amazing.  Even at the higher touch counts, I've been seeing response times similar to the 2 and 4 touch frames. 

I'd like to talk about the second bit of news that came out of our friends at ZaagTech recently.

The introduction of the new frame brought with it a new iteration of the ZinFrameServer application -- Version 5.5.x.  The key change is the way this tool set runs on the installed system.  First let me state that for the purposes of this article, I'll be specifically discussing the Windows version of the tools, as the Mac tool is still a separate animal and has not changed all that much.

First off, the driver runs as a Windows Service.  This is key for allowing the frame to operate at the log in screen level.  The system-tray option is still accessible so the service is easily managed from the desktop.  Additionally, this version of zinFrameServer is exceptionally good at switching between frames in a multi-frame configuration.  

Interesting additional data is now visible via this tool.  You can see what version of hardware you're running off of, as well as seeing what type of frame configuration you're working with.  

Another neat feature in the new tool is an automatic pairing of touch frames.  If you connect more than one touch frame overlay to a single system running v5.5.1 or better, you'll see a drop down containing the serial number for each frame attached.  You can switch between these frames and enable TUIO, HID, Flash, or any combination of these independently for each frame!

Full Windows 7 and 8 touch support is implemented with this most recent driver update. 

Continue Reading

5 New Machine Code Games Titles Launched!

 We've launched 5 new games today in conjunction with Machine Code Games.

The new games are as follows:

The Battle Home: A Pachisi Game - This is very similar to the classic Parcheesi board game of yore.  I’ll admit I’ve lost of a lot of time to testing and retesting this game—not all of that time loss was due to a _need_ to test, if you know what I mean.  The game can be played with up to four players independently or on teams.  The default install includes two game boards, a square one and a “plus” shaped one.  There are lots of play options and game play itself is easy to manage as the game seamlessly guides you through valid moves.  The AI is remorseless. 

Fas’Jack - This one is Blackjack for 1 - 10 players.  The AI is pretty solid and the players play against the house so hiding your cards is not required.  The game plays in 10 rounds with the player with the highest stake winning the set.  Each round, every player is awarded a $5 bump in their stake so no player is every knocked out of the game entirely before the 10th round ends.  Fun for casual as well as serious blackjack fans.

Bloody Hearts - This one is a redux of the classic card game Hearts with a darker twist.  The art and appearance of this one are ominous.  The game can be played with touch only, but exposing and selecting your cards can be tricky in this mode.  Ideally this game is best played with cardboard blinds to obscure your hand from your foes...er… opponents. 
A solid translation of Hearts, this game can be played by 1 - 4 players singly or on teams.  The AI is quite good at the game.

GotIt - A frenetic shooter game, GotIt is a 1 - 4 player game where you fire beams attempting to destroy an invading infection.  The mechanic is simple.  You’re one of 4 corners of the screen.  Your space can fire several beams at the same time, but every beam costs you battery.  When your battery is depleted you cannot fire.  Your battery recharges.  There are point targets, power ups and power downs.  Fun, quick paced, but definitely a game that is better played with others.

Pair Soup - Matching game for 1 to whatever players.  The only real limitation for players on this game is number of track-able touch points and screen size.  I’ll be honest, I keep trying to not like this game but I just can’t do it.  The concept is simple, a slew of preset silhouettes pop onto the screen and you and your friends attempt to match all the pairs.  When all available pairs are matched more pop onto the screen.  Each “round” more and more objects appear and not all objects that appear will have a match.  Addictive and straight forward.  The game supplies three modes of play currently.  Each mode is based on the shape selection.  The “Basic” mode is colored shapes that are mostly animal, kid friendly shapes.  The “No Color” option are shapes with no color… very tricky.  The “Skulls” mode is a vast selection of skull-like shapes that introduce a collection of not-immediately-recognized objects.

For those of you familiar with Machine Code Games, these new titles are compatible with the free MCG Application Launcher. Additionally, the games offering the ability to modify the art assets once installed.  For instance you could easily modify Pair Soup to add custom art in place of the skulls or bunnies collections.

We've also created a value bundle for these games located here.

Continue Reading

New X Slim Series from ZaagTech

ZaagTech has launched their newest addition to their product line.  An X Series frame which sports the lovely additional feature of being extremely thin!  This new frame measures in at roughly 19mm wide, versus 36.5mm, while preserving the 11mm height from the previous X Series frames.  In addition to this new dimension, the frames use a new connection setup which places the screws on the outside edge of the corners.  The new screw setup, 4 screws per corner, allows for a much stronger bond than previous models.  

Like the standard X Series frames, the new X Slim are jacketed in black extruded aluminum.  A single USB connector hangs from the lower right (when facing the frame) corner of the device.  

The frame is advertised as offering 2x the speed of it's predecessor.  We'll have to run some tests to determine if the product can delivery on this claim! 

The overall look and feel of this new frame is rather nice.  The things that I noticed immediately were the rigidity of the corner connections and a significant thinning of the lower edge.  In previous versions of this frame the interior edge had the same sized lip on the top and bottom, this new frame has virtually no lower lip to the IR window.  This should allow for the frame sensors to sit very, very close to the touch surface.

Another post should be coming shortly where we'll run some side by side comparisons with some of the other frames.

Continue Reading